Mill Operator - 1st Shift

Operations Rice Lake, Wisconsin


Description

MILL OPERATOR

 

Prep. By: SLB/BLD

Appr. By:

Iss. Date: 7/19/2012

Rev. Date: 10/2016

 

MJD No:

HR Job No:

Job Grade: 3

Job Points: 239

Department Code (s):

 

 

 

 

JOB DESCRIPTION:

 

Compliance with safety rules required at every operation.

 

Quality inspection required at every operation.

 

This description represents the most significant job duties but does not exclude other work duties assigned or required but not mentioned, the inclusion of which would be conformity with the factor degrees assigned.

 

Work from prints, sketches, specifications, instructions to order and maintain stock, check coil dimensions, load, adjust reel, decoiler, feed, cut-off, facial bow, coolant, check work, monitor equipment, ensure absence of dents, scratches, roll marks, unacceptable defects; mix coolant, oil, clean dies, lubricate equipment, perform minor maintenance work, notify superior of unusual conditions, equipment malfunction, material discrepancies; load finished parts on carts, dispose of scrap, maintain equipment, work area in clean, orderly condition.

 

-          Perform duties to operate/maintain roll form equipment, able to make simple adjustments to maintain close tolerances and sizes.  Not required to perform set-up functions.

 

Use all precision measuring instruments, gages, fixtures, machinists' common hand tools, power driven tools, appropriate material handling equipment.

 

Fill out production reports, daily logs, finished goods cards; store requisitions neatly and accurately.  Must understand the importance and significance of each.

 

Must be perform and document all quality checks as required.

 

Must work overtime on short notice, as required.

 

 

 

 

 

FACTORS

SUBSTANTIATING DATA

DEG

PTS

Education or Trade Knowledge

Use simple arithmetic.  Work from complicated prints, sketches, setup sheets, specifications, instructions.  Use scale, square, gages, micrometer, vernier, indicator and other precision measurement instruments.  Must have technical and problem solving skills.

  3

42

Experience

Over three (3) and up to twelve (12) months to become familiar with equipment, operation, adjustment, quality standards, checking procedures, department practice.

2

44

Initiative and Ingenuity

Somewhat repetitive work.  Duties to operate coil forming equipment on light gauge aluminum and steel coiled stock.  Some judgement required to adjust to maintain close tolerances, make minor repairs, following prescribed routines and carrying out instructions.

2

28

Physical Demand

Light physical effort, equivalent to frequently moving or handling light weight material up to 25 pounds, occasionally moving average weight material over 25 and up to 50 pounds and rarely moving heavy weight material over 50 pounds, assistance from others or lifting devices is available for material over 50 pounds.

2

20

Mental and/or Visual Demand

Continuous mental and/or visual attention required to check coil, stock, load, adjust equipment, monitor, gauge output, and eliminate dents, scratches.

3

15

Responsibility for Equipment or Process (1990 Costs)

Error, carelessness in adjustment may result in damage to equipment requiring repair, downtime.  Probably damage over $250 but seldom over $1000.

3

15

Responsibility for Material or Product (1990 Costs)

Carelessness, failure to check output may necessitate, require scrapping.  High production equipment, high volume of scrap.  Probably losses over $500 but seldom over $1,000.

3

15

Responsibility for Safety

of Others

Reasonable care in performing own work is necessary to prevent injuries to others.  An injury should it occur, would result in minor injuries, such as cuts, abrasions, burns or bruises.

2

10

Responsibility for Work

of Others

Responsible for own work only.

1

5

Working Conditions

Somewhat disagreeable working conditions.  Exposed to noise, heat, oil or coolant, and cleaning agents with one continuously present to the extent of being objectionable or with several elements present to the extent of being objectionable but usually not more than one at one time.

3

30

Hazards

Exposed to lost time hand, foot injuries when handling coils, making adjustments.

3

15

 

 

 

 

 

 

 

 

 

AMERICAN WITH DISABILITIES ACT

POSITION DESCRIPTION ADDENDUM FORM

 

 

 

 

 

 

JOB TITLE

Mill Operator

 

DIVISION

Rice Lake

REPORTS TO (TITLE)

Production Supervisor

 

DEPT

 

JOB GRADE

3

 

JOB NO.

 

 

Based upon the attached position description, the following are the requirements for the above listed position:

 

 

 

 

 

 

Essential Functions:

In Order of Importance

 

% Of Time Required

What is Done

1.

Operating Equipment /Quality Checks

65%

Inspect product off mill

2.

Material Handling

10%

Keeping materials and lubricants in mill

3.

Scheduling and Programming

10%

Input orders from dispatch to controller

4.

Adjustments

10%

Adjustments to straightness controller and lubrication.

5.

Lean

5%

5S

 

Essential Physical and Mental Requirements:

 

Physical: (sitting, walking, climbing, lifting, etc.)

 

Working with mechanical parts and machines. Working with chemicals. Any hazardous chemical exposure is specifically defined on accessible Material Safety data Sheets.  Frequently moving or handling light weight material up to 25 pounds, occasionally moving average weight material over 25 and up to 50 pounds and rarely moving heavy weight material over 50 pounds, assistance from others or lifting devices is available for material over 50 pounds. Balancing, stooping, reaching, standing, walking, pushing, pulling, lifting and grasping

Sensory: (visual, hearing, speaking, smell, etc.)

 

Feeling, seeing, hearing, speaking, eye and hand coordination.

Mental: (reading, writing, reasoning, analyzing, learning, etc.)

 

Communication, interpersonal skills as applied to interaction with coworkers, supervisor, the general public, etc. sufficient to exchange or convey information and to receive work direction.

Other:

 

Incumbent assembles vertical and horizontal pieces within customer specifications in a timely manner to meet internal and external needs. Completed other tasks as needed.

 

 

Minimum Qualifications: (Education/Experience, Skills)

Over three (3) and up to twelve (12) months to become familiar with equipment, operation, adjustment, quality standards, checking procedures, department practice.

 

 

 

Completed By:

 

 

Date:

 

Supervisor's Signature

 

 

Date:

 

Current Incumbent's Signature

 

 

Date:

 

Human Resources Manager

 

 

Date:

 

 

MANUFACTURING JOB DESCRIPTION

Page 1 of 4

MJD-468

Rev.  02/2016